Lincoln Nautilus: Seatbelt Systems / Locked Seatbelt Retractor Releasing. General Procedures
Repair
NOTE:
If the seatbelt webbing does not extract from the seatbelt
retractor from the stowed position, this may be due to a normal
condition which happens when the seatbelt retracts at a high rate of
speed. Follow these steps to release the seatbelt.
Front row seatbelt retractor
NOTE:
Typical front outboard seatbelt retractor shown, other configurations similar.
NOTE:
To unlock the seatbelt retractor, only a few millimeters
of seatbelt are necessary to retract back onto the seatbelt retractor
spool.
-
Slowly lower the seatbelt shoulder height adjuster
allowing the seatbelt to retract back onto the seatbelt retractor spool.
If the seatbelt shoulder height adjuster is all the way down, proceed
to step 3.
-
Slowly extract the seatbelt from the seatbelt
retractor. If the seatbelt does not extract, proceed to the next step.
-
Firmly pull and extract as much seatbelt from the seatbelt retractor as possible.
-
-
Slowly feed the seatbelt slack back into the retractor to unlock it.
-
Slowly extract the seatbelt from the seatbelt retractor. If the seatbelt does not extract, proceed to the next step. If the seatbelt does extract, proceed to step 8.
-
Remove the fastener and detach the seatbelt anchor
or seatbelt anchor and pretensioner. REFER to the appropriate removal
and installation procedure in this section.
-
-
Slowly feed the seatbelt slack back into the retractor to unlock it.
-
Slowly extract the seatbelt from the seatbelt retractor. Proceed to the next step.
-
-
If the seatbelt does not extract, install
a new seatbelt retractor. Refer to the appropriate seatbelt retractor
removal and installation procedure in this section.
-
If the seatbelt does extract, install all
fasteners that were removed and tighten them to specification. REFER to
the appropriate removal and installation procedure.
-
Check the active restraint system for correct operation by carrying out the appropriate functional test.
Refer to: Seatbelt Systems (501-20A Seatbelt Systems, Diagnosis and Testing).
Rear seatbelt retractor
NOTE:
Typical rear outboard seatbelt retractor shown, other configurations similar.
NOTE:
To unlock the seatbelt retractor, only a few millimeters
of seatbelt are necessary to retract back onto the seatbelt retractor
spool.
-
Slowly pull the seatbelt out as far out as possible.
-
-
NOTE:
Compressing the backrest foam and/or
reclining the rear seat backrest (if equipped) allows more slack of the
seatbelt webbing to be fed into the seatbelt retractor.
Compress the backrest foam pad and recline the rear seat backrest (if equipped).
-
Slowly feed the seatbelt slack back into the
retractor to unlock it. If the seatbelt does not extract after carrying
out this step, proceed to the next step.
-
Firmly pull and extract as much seatbelt from the seatbelt retractor as possible.
-
-
Slowly feed the seatbelt slack back into the retractor to unlock it.
-
Slowly extract the seatbelt from the seatbelt retractor. If the seatbelt does not extract, proceed to the next step. If the seatbelt does extract, proceed to step 16.
-
Remove the fastener and detach the seatbelt anchor
or inflatable seatbelt union (if equipped). REFER to the appropriate
removal and installation procedure in this section.
-
-
Slowly feed the seatbelt slack back into the retractor to unlock it.
-
Extract the seatbelt webbing from the seatbelt retractor. Proceed to the next step.
-
-
If the seatbelt does not extract, install
a new seatbelt retractor. Refer to the appropriate seatbelt retractor
removal and installation procedure in this section.
-
If the seatbelt does extract, install all
fasteners that were removed and tighten them to specification. REFER to
the appropriate removal and installation procedure.
-
Check the active restraint system for correct operation by carrying out the appropriate functional test.
Refer to: Seatbelt Systems (501-20A Seatbelt Systems, Diagnosis and Testing).
Symptom Chart(s)
Diagnostics in this manual assume a certain skill level and knowledge of Ford-specific diagnostic practices. REFER to: Diagnostic Methods (100-00 General Information, Description and Operation)...
Cleaning
WARNING:
Do not bleach or re-dye the seatbelt webbing, as the webbing
may weaken. Failure to follow this instruction may increase the risk of
serious personal injury or death in a crash...
Other information:
Check
NOTE:
Road Force® values in illustrations are shown in pounds.
NOTE:
Match mounting is a technique used to reduce radial runout
or road force on wheel and tire assemblies. Excessive runout is a source
of ride quality complaints and match mounting can be used to minimize
the runout...
Heated Seat Precautions
WARNING: Use caution when using
the heated seat if you are unable to feel
pain to your skin because of advanced
age, chronic illness, diabetes, spinal cord
injury, medication, alcohol use, exhaustion
or other physical conditions...