Lincoln Nautilus Manuals

Lincoln Nautilus: Glass, Frames and Mechanisms / Lead Terminal Repair. General Procedures

Materials

Name Specification
Motorcraft® Ultra-Clear Spray Glass Cleaner
ZC-23
ESR-M14P5-A
 

Repair

  1. Bring the vehicle up to at least the specified room temperature or above.
    Temperature: 60.8 °F ( 16 °C)
  1. NOTE: The new terminal covers the original terminal location, but it must be placed so the terminal conductive areas will be placed on a good conductive base.

    • Terminal Kit — Back Glass 4F1Z-14421-AA
    Clean the bus bar in the area to be repaired with grey scuff pad (600 to 1000 grit), and then with glass cleaner to remove all dirt, wax, grease, oil or other foreign material.
    Material: Motorcraft® Ultra-Clear Spray Glass Cleaner / ZC-23 (ESR-M14P5-A)
  1. NOTICE: Do not use any type of flame torch or flame-heated soldering gun for this procedure. Use of these tools provide inadequate heat generation at the tip and the exhaust heat can cause damage to plastic trim parts in the area. Use only an electric soldering gun with 100 watts or more of power. Before using the soldering gun, be sure to melt a small amount of rosin core solder to the tip. The solder will assist in achieving better heat transfer from the soldering gun tip to the new terminal.

    NOTE: Depending on the original terminal location, and whether the terminal is covered by pillar trim, determines where to locate the new terminal. Some grid line bus bars may only allow the placement of the terminal above or below the original tab location due to space limitations. For most vehicle applications, the replacement tab location covers the original tab location, but still allows the replacement tab to attach to the bus bar on good conductive material.

    Place the replacement terminal type A over the original tab location, making sure the conductive areas of the terminal will be on a good conductive area. Do not place the terminal tab foot on the original location, which does not have conductive material.
  1. Hold the terminal in place with an item such as a regular lead pencil at a 90 degree angle from the terminal (Holding at other than a 90 degree angle may allow the terminal to slip when the solder liquefies).
  1. NOTE: The new terminal has pre-applied solder, flux and temperature-sensitive paint. The paint provides a visual indication when the terminal has reached the correct temperature to melt solder on the terminal. When the correct temperature is achieved, the temperature paint liquefies and changes color.

    Place the soldering gun tip on the top of the terminal, but not on the painted areas of the tab. Energize the soldering gun and watch for the painted area of the terminal to liquefy and change color. The paint should liquefy in approximately 25-45 seconds after heating. As soon as the paint color completely changes on either side of the terminal, de-energize the soldering gun and continue to hold the terminal in place with the soldering gun and pencil for an additional 30 seconds.
  1. Remove the soldering gun and pencil from the terminal. Allow the terminal to cool for another 2 minutes before attaching the wiring lead to the terminal.
  1. Attach the electrical lead connection to this terminal, turn on the heated rear door window glass and verify the operation.

    Heated Window Grid Wire Repair. General Procedures

    M..

    Power Door Window Initialization. General Procedures

    Initialization NOTE: NOTE: Initialization is required to learn both the full UP and full DOWN positions and the profile of the glass as it travels through the glass channel...

    Other information:

    Lincoln Nautilus 2018-2024 Service Manual: Rear Suspension - Component Location. Description and Operation


    NOTE: AWD suspension shown, FWD similar. Item Description 1 Coil spring 2 Stabilizer bar and links 3 Shock absorber 4 Wheel knuckle 5 Wheel bearing and wheel hub assembly 6 Wheel studs 7 Lower arm vertical link 8 Toe link 9 Lower arm and bushing assembly 10 Upper arm ..

    Lincoln Nautilus 2018-2024 Service Manual: Safety Precautions - Overview. Description and Operation


    Overview   WARNING: Before servicing any tire, ask the customer if anyone injected a tire sealant into the tire. Tire sealants may be flammable and can burn or explode if exposed to an ignition source. Failure to follow this instruction may result in serious personal injury. NOTICE: Do not clean aluminum wheels with steel wool, abrasive-type cleaners or strong detergents or da..

    Categories

    Parking Aid Indicators. Parking Aids – Troubleshooting

    Parking Aid Indicators

    Lincoln Nautilus. Parking Aid Indicators. Parking Aids – Troubleshooting

    The system provides object distance indication through the information and entertainment display.

    As the distance to the object decreases, the indicator waves and the lines move toward the vehicle icon. If there is no object detected, the distance indicator lines are grey.

    read more

    Copyright © 2024 www.linautilus.com