Lincoln Nautilus Manuals

Lincoln Nautilus: Rear Suspension / Wheel Knuckle - FWD. Removal and Installation

Lincoln Nautilus 2018-2022 Service Manual / Chassis / Suspension / Rear Suspension / Wheel Knuckle - FWD. Removal and Installation

Special Tool(s) / General Equipment

Vehicle/Axle Stands

Removal

NOTICE: Suspension fasteners are critical parts that affect the performance of vital components and systems. Failure of these fasteners may result in major service expense. Use the same or equivalent parts if replacement is necessary. Do not use a replacement part of lesser quality or substitute design. Tighten fasteners as specified.

  1. Remove the wheel bearing and wheel hub.
    Refer to: Wheel Bearing and Wheel Hub - FWD (204-02 Rear Suspension, Removal and Installation).
    1. Remove the wheel speed sensor harness bracket bolt and position the bracket aside.
    1. Remove the brake hose bracket bolt and position the bracket aside.
  1. Raise the suspension to curb height.
    Use the General Equipment: Vehicle/Axle Stands
  1. Remove the lower arm vertical link.
    Refer to: Lower Arm Vertical Link (204-02 Rear Suspension, Removal and Installation).
    1. Remove and discard the lower arm-to-wheel knuckle bolt.
    1. Remove and discard the toe link-to-wheel knuckle bolt and nut.
    1. Remove and discard the upper arm-to-wheel knuckle bolt and nut and remove the wheel knuckle.

Installation

  1. NOTICE: Tighten the suspension bushing fasteners with the suspension loaded or with the weight of the vehicle resting on the wheels and tires, otherwise incorrect clamp load and bushing damage may occur.

    1. Position the wheel knuckle and install the new upper arm-to-wheel knuckle bolt and nut.
      Torque: 76 lb.ft (103 Nm)
    1. Install the new toe link-to-wheel knuckle bolt.
      Torque: 129 lb.ft (175 Nm)
    1. Install the new lower arm-to-wheel knuckle bolt.
      Torque: 203 lb.ft (275 Nm)
  1. Install the lower arm vertical link.
    Refer to: Lower Arm Vertical Link (204-02 Rear Suspension, Removal and Installation).
    1. Position the brake hose bracket and install the bolt.
      Torque: 124 lb.in (14 Nm)
    1. Position the wheel speed harness bracket and install the bolt.
      Torque: 80 lb.in (9 Nm)
  1. Install the wheel bearing and wheel hub.
    Refer to: Wheel Bearing and Wheel Hub - FWD (204-02 Rear Suspension, Removal and Installation).
  1. Check and if necessary adjust rear toe.
    Refer to: Rear Toe Adjustment (204-00 Suspension System - General Information, General Procedures).

    Wheel Knuckle - AWD. Removal and Installation

    Special Tool(s) / General Equipment Vehicle/Axle Stands Removal NOTICE: Suspension fasteners are critical parts that affect the performance of vital components and systems...

    Wheel Studs. Removal and Installation

    Special Tool(s) / General Equipment Hydraulic Press Removal Remove the wheel bearing and wheel hub. Refer to: Wheel Bearing and Wheel Hub - AWD (204-02 Rear Suspension, Removal and Installation)...

    Other information:

    Lincoln Nautilus 2018-2022 Service Manual: Vehicle Dynamic Suspension. Diagnosis and Testing


    DTC Chart VDM DTC Chart Diagnostics in this manual assume a certain skill level and knowledge of Ford-specific diagnostic practices. REFER to: Diagnostic Methods (100-00 General Information, Description and Operation).   DTC Description Action C110C:11 Left Front Damper Solenoid: Circuit Shorted to Ground   GO to..

    Lincoln Nautilus 2018-2022 Owners Manual: Locating the Blind Spot Information System Sensors. Blind Spot Information System Indicators. Blind Spot Information System – Troubleshooting


    Locating the Blind Spot Information System Sensors The sensors are behind the rear bumper on both sides of your vehicle. Note: Keep the sensors free from snow, ice and large accumulations of dirt. Note: Do not cover the sensors with bumper stickers, repair compound or other objects. Note: Blocked sensors may affect system accuracy. If the sensors become blocked, a message may appear in the i..

    Categories

    Auto-Start-Stop

    What Is Auto-Start-Stop

    The system is designed to help reduce fuel consumption and CO2 emissions by stopping the engine when it is idling, for example at traffic lights.

    Auto-Start-Stop Precautions

    WARNING: Apply the parking brake, shift into park (P), switch the ignition off and remove the key before you leave your vehicle. Failure to follow this instruction could result in personal injury or death.

    WARNING: Apply the parking brake, shift into park (P), switch the ignition off and remove the key before you open the hood or have any service or repair work completed. If you do not switch the ignition off, the engine could restart at any time. Failure to follow this instruction could result in personal injury or d

    read more

    Copyright © 2022 www.linautilus.com